Logitech G29 Wheel Wobble Repair Guide

Do you see any problem about adding lock washers in those screws so it does not happen again?

Thanks for the thorough coverage of the disassembly. That'll be a big help!

You, my man, are a life savior. But before I mess around with mine, I think I'll wait until the warranty ends in june. At least I already found a good video to guide me on that.

Mine FINALLY let go last night after its last drift session before I switched over to an F1 car and realized how much movement there was in the base... I guess I hadn't noticed since the wheel was always spinning lol

Thanks for the save Boss! I'm assuming a 2 hour job from start to finish? 1.5

my wheel is stuck on tight so I cant lock it on to my desk
and I keeps falling

You are an absolute Legend man, thank you so much!🙏

I did like you said in the video but it was not screws holding the gear drive mechanism to the shroud that were causing the wobble but the three long screws that attach the wheel itself to the hub are causing the wobble unlike your wheel my wheel that wobbles up and down my one wobbles side to side.
I have no idea how to fix it. I tried paper fittings where the screws are but they just get torn apart.
maybe you can help

Mine isn't the whole centre shaft moving like yours.... just the wheel itself has come loose and wobbles,looking behind the wheel and wobbling it shows that none of the centre piece moves at all

As it appears to be a common problem i wonder why they haven’t fixed it at the manufacturing point???

should the wheel still have a little bit of wobble in it because i got mine 2 days ago and it has wheel wobble a little bit

thanks bro this helped. Anyone who is doing this please be aware that those 4 black screws on the bottom. DO NOT REMOVE THEM. It will cause the wheel to jiggle and the black plastic piece that keeps the wheel from spinning endlessly could move. I found out the hard way. Thanks

Thank you very much sir
The best how to video on this in my opinion
High five from Denmark
A member of Amigos Racing Team UK 🇬🇧

moi le probleme venait des 4 vis qui tienne le chassis interne sous le volant qui etait cassé.....rajouter des vis plus longue et des rondelles contre le chassis et c est terminer 😁😁

What dimension or size on the screws under the wheelbase tightened in holes? (x8)

I don't have wheel wobble like yours. I have a loose left and right turning problem. Do you know how to fix that? If the steering wheel is perfectly centered, the wheel is loose from about the 11 o'clock position to the 1 o'clock position. I want to make that tighter but idk how.

Thank you so much for this video. Didnt have any wobble but needed to remove the clamps to replace them with extra long 3D printed ones to fit onto my extra-thick desk. This video was by far the most useful for the teardown, so it's appreciated!

This helped so much thank you!

DamN! What a poor design from Logitech!. My wheel is only 4 months and already giving this problem. Thx for your help.
Could we find a definitive way to avoid this happen in the future. I Think it is not nice to be doing this procedure frequently.

awsome video thank you. i have the same issue. will fix it soon. thank you for the video

Thanks for this video. I don't know if you can help me but I bought one of these wheels off a friend (he didn't look after it). It works fine and isn't wobbling but it does feel a bit "grindy" when in use and doesn't feel smooth when turning it. Can you offer any advice or support at all? Many thanks.

Great presentation, every helpful. Thank you

Holy shit at the redundancy of the amount of unnecessary screws in this thing. All that's needed to reassemble is the front 6 hex screws. Fuck all the rear screws lol.

Thank you very much for this. It fixed my wheel for me. 🍻

After fixing up the screws, the wheel stopped wobbling. But after playing for a bit the wobble started again… any ideas guys?

Thanks for the video, well done. Since this seems to be a common issue I'm going to put a drop of super glue on the side of the screw heads that cause the wobble after I tighten the screws.

hi, I need your help I just lost the 6 screw from back of the wheel. what size exactly is that screw?

I have a problem when i turn the wheel completely the wheel start to bounce and i lose the alignment with the game, what can i do?

I did the same repair but after that the steering wheel does not calibrate can you tell me what I should do

I have a G29 joystick, and when I turn it on in PS4 mode, it keeps spinning and does not stop, so what is the solution?

is it normal for the wheel to have like a mm amount of wobble side to side?

My G29 didn't have the wobble issue, but i was trying to solve my clunk issue when hitting the full lock. This video just helped me, where which screw came from where.

get some spring washers on to keep the tension on the screw as will help to stop it backing out or if you want you could use Lock Tight Thread Lock but if you ever need to take out the screw its going to be a hasle

One of the best videos showing us how to dissamble a G29 correctly

Anyone know the value of FB1 at the wheel board?

Even if you tighten them screws back up it will highly likely fail again soon. The plastic has weakened and became brittle. I done a vid on bolting it back together which will fix this solid its tricky but can be done without further dismantling or damaging the big internal cog . Or you could perhaps superglue the original screws back in but thats supertricky and got to be fast. Dont know how effective it would be.
Other options are i hear theres a metal housing that can be bought on amazon. But thats more cost and alot more dismantling. involved.
Never buy a second hand g29

Thanks mate

Thank you. I have the wobble and I will be trying this soon as I get home

I guess over time , the weight of your hands and arms hanging off the thing at a weird angle putting pressure on it , is the course

what size hexagon screwdriver do you use?

Thank you, now i can play without those wobbles

that's what I'm looking for... Thank you so much brother 🤜🏻

Still same problem, i did everything like you did in video....

I'm really thankful! Really clear and well explained. Worked with my g920!

My brand new G29 had also quite a big wobble. Strangely enough, when disassembled, i didn´t found any loose screw. Everything was tight from factory. So when it was all disassembled, i at least added some more lubricant to all the gears and oil into the top bearings under the brass pinion gears. When assembling - you need to apply Loctite on the black screws holding gearbox in place - at least on the four that are at bottom of the unit - there are tightened agains plastic so they can´t be tightened with a big force otherwise plastic under the screw cracks. Well after assembling it - wobble simply disappeared, wheel is now tight and feels great. Don´t know where the problem was but it´s gone.

hi i have a problem with my g29, when there is the feedback hole turning to the right the steering wheel makes a loud noise of gears, as if it were creaking. if instead i turn to the left it is silent. Do you know by chance how to solve it? thanks

my screws dont work anymore and now they are stuck

watching this in 2025. thankyou man! solved mine.

ive tryed ure method and its not solved the problem.maybe other issues.i have big movement on my wheel