Simple DIY 18650 Battery Charger - TP4056 Review (Everything Explained)

Awesome video! If you ever make a new version, you should consider using a 12V input & some cheap buck converter modules, that way you can power it with a more conventional amp & volt figure. Also, what's up with that soldering iron you're using? What is its brand? :o

💚💚💚

Why you've used 4 tp4065? It's not possible to use 1 for all the batteries???

super nice video

Helo
Can i use this module(HX-3S-FL10A)
For 6 lityom ion batteria
3 seri&3 paralel

I have a question tat maybe someone could answer? if I pluck this charger that sarin made on a 5V 30A (from an ATX) power supply. What will happen? will burn all the TP4056 or they will draw only 1A each and there for only 4A? I appreciate any answer. Thank you

good jop but very comlicated

HI SORIN can we reload 16650 battery on 18650 Charger ?

ok but dont u need a balancer or BMS for this? or is there an option that u can charge all 4 Batterys with one big charger

Felicitari Sorin. Ne esti de mare ajutor. Frumos, explicit, concret, de la inceput pana la sfarsit. Multumesc pentru prezentare si explicatii.

super tutorial fratiuc poti sa mi spui de unde ai cumparat toate cele pentru video.?

You can get those charging modules for ~50 cents, you are being ripped off.

Why u use 4 pcs tp 4056 module? If I use 1pcs 4056 module for 5 battery chargeing what the problem I face?

A T12 soldering pen is cheap. 😬

I can use this module for two 3.7 volt lithium battery in parallel at a time.

Can I use This module is used as BMS ?

Did you learn English with Ion Iliescu? Your English accent sounds like him 😁

These are great skills needed for the future!!!!

how to draw power from the same?

Is this module used to charge cell phone battery?

ah thats what look like in laptop batteries

too much expensive of TP4056 you can use 1 chip cause the battery are parallel and the output are 3.7v

can you plug more than 1 charger? I mean, plug 2, 3 or 4 usb plugs (1 per board). Would it work? Would it explode?

So using a chinese parts to make a charger is better than charger thats made in china..?

SALUT.
Nu am inteles cum le incarci oe toate odata cu un incarcatot de tel sa sounem?
Imi poti explica cum ?
Multumesc.

SALUT.
Pentru doi acumulatori si doua module la 5V , ca amperaj trebuie?

i made something like this and i use a computer power supply

hello good job
the wire that replaces the pin connectors, is it really 0.8mm²?
because it fits easily into the holes of the card, it looks like 0.5mm²

Foarte bine explicat ! Bravo.

Can this charging method be applied to 3S 18650 system using the TP4056 module , and have a secondary wiring for the batteries to provide 12v output isolated by a 3way on/off0n switch ?
The 3S modules are not very good , I like the TP 4056 better .

Thank you for the simple and awesome DIY you helped me make my own charger

Do the chargers work with normal li-ion aa batteries?

How to charge and Use 18650 battery at the same time?

You'll probably be surprised to find out that the charging module are also made in China.

Great just what I needed for my project it would have nice put a picture of the wiring diagram.

Dude, I really like your videos and the way that you mention the cost of equipement👌

stop the music, l have to watch it muted.

Devi usare stagno con anima dissaldante ; e prima di avvicinare il saldatore va solo ben scaldato e pulito , poi avvicinato facendo contatto ai piedini da saldare , e solo dopo si aggiunge lo stagno ; altrimenti le zampine non si scaldano e lo stagno risulta incollato e non saldato 😏😘😁😁

much better using fast charger type C charging module not micro

Sorin please tell me which is faster and better, a TP4056 module or a HT3786D ic chip?
Also is there now a module or IC chip with USB type C fast charging?
I am learning which be the best to build my charger. Thanks!

Nice videio...

Tp4056 is a game changer for me😅

Hey Sorin. Where do you buy the tp4056?

Why not just one module?

what type of soldering iron is that >?

What if i use a more powerful charger but only input one cell will it take all the current or the module limit it to a maximum ?

Hi, i have a question. If i have 2 chargers of 2 amps each. If i put them at the same time, do i have the 4 batteries charged at 1 amp each ? Thank you if you can reply because i want to do the same but with 8 batteries cells and 8 TP4056 to charge them at 500mA each with 2 chargers of 5v 2amps.
OH i have another question by the way:
If i use 1 TP4056 for 2 battery cells (so in parallele, not in series) SO 1 TP4056 will charge them at the same time with 500mA SO 1 TP4056 can charge 2 batteries at the same time OR is it dangerous because il the battery cells have not the same voltage in // it will over warmed ?

Liitokala m4s cost 16usd better buy that sometimes commercial product is better than diy

Making the circuit board makes the product expensive also there is no need for it also most of the copper is not comming in used and is dissolved