How to Build Ultimate Budget FPV Drone Build 2021 // Beginner Guide

Best tutorial! I was able to solder a 18650 to my gmas pacemaker! Thank you

What is the RX and TX used in the drone and the remote ??

Flux...

Please make more build videos!! I love it!

do it but in 2024

The most crucial part of a quadcopter is the frame and other mechanical parts. If you save money on a frame an expensive ESC wouldn't fix it.

Do you have a temp for soldering and a solder size to buy?

Which controller and google u use in budget please?

how much weight does it lift?

what frame is that? the link to it doesn't exist anymore.

Brown Robert Miller John Moore Mary

Thanks for the quad tutorial

Williams Thomas Hall Kevin Johnson Maria

Davis David Jones Amy Young Donald

I want the link to the second part of this video

You need a Soldering Fume Extractor it will save you from sickness

The more pins the more features you can add

Who told you that lie that the black wire acts like a heat sink?? 😂😂😂

Thanks for putting this video out. I especially appreciate your soldering tips!

What can I use as an alternative if I don't have goggles? Is there way to show the camera stream on a simple laptop of notepad?

liked and sub

what if someone buy the parts and pay you to build it would you

2024 but no part 2?

How much money for this project

This is amazing. I really want to build my own, i'm sick and tired of DJI's fly software thinks im in a no-fly zone because I live near a disused airfield that hasn't been used since WW2. I've written to DJI about it but they don't care one iota.

As detailed and as fast as possible is a contradiciton in itself. in the trash it goes.

funny question yet important to me, how much weight can it carry, I might send it down to carry small packages

so many missed opportunities for "just the tip" jokes...

Can anyone please repost best motors and best frame model names, because the links direct me to the site saying product out of stock and does not show exact model.
Thanks on advance

Ehhh build

How good is this in 2024? And any idea what the total cost would be?

Hey, good.

“If you put it in backwards it will blow in your face…so just keep that in mind” 💀💀🤣🤣🤣🤣🤣

nice project, but you definitely need training in soldering.

I see you never did the setup video or even link one ? can anyone point me in the right direction on how to set this up once its built ?

I like a 2 irons setup - one with a flat tip - one point. Wide is just to heat the wire and tab just enough to prime them with soldier. Then do the fine work and clean up with the point. That keeps me from, over heating the board. It also heats everything evenly faster, with less hot spots.

Also, good soldier and flux matters. ESP. when you start out.

I tried to configure according to your video although preview responds according to the remote control. However, the motor does not spin, even though I am able to control motors using app.

Thanks!

You definitely need to take a soldiers course, you're a nightmare to waych

There's something I'm struggling to understand. In rc planes, you buy a transmitter and a matching receiver. In FPV drones the receivers seem to be open source?? So can I put a flysky receiver in an FPV drone instead of an open source one in order to be able to use my flysky i6x transmitter? Thanks a lot

Hi and the software put link to the software please

Get a finer point on your soldering iron it dramatically reduces bridges.

The links in the pinned comment more than half of them are not available anymore. Can you update that list?

great vid! i've been watching a lot of them and studying before i pull the trigger on my first build. Question, the frame I want has listed as a frame that can hold a 30.5 x 30.5 stack. the stack i found I want is described as a 30 x 30 stack. Is the .5 difference an issue or is that close enough?

Hi @DroneMesh how much did it cost for this drone thank you

lol battery wires, like on 3kW electric motor